How to Detail: 07 GTI Step by Step Full Correction By Nikku - Acura Forum : Acura Forums
Detailing Tips and Tricks Need some shine? Tired of swirls? Step on in!

 
LinkBack Thread Tools Display Modes
post #1 of 11 (permalink) Old 11-16-09, 06:41 PM Thread Starter
Auto Detailing Nerd
 
nikku's Avatar
 
Join Date: Apr 2009
Location: Toronto
Posts: 50
How to Detail: 07 GTI Step by Step Full Correction By Nikku

VW GTI Full Correction Ė Step by Step Write-Up

A few months ago I promised to detail my cousins VW GTI however I have been busy with client details and I wanted to make sure that I had enough time to take a lot of step by step pictures and do a full correction.

Ok so to the present day. My cousin went on vacation so I chose two days out of the two weeks he was away to work on his vehicle. Thankfully our schedules worked out and I had freed up two days so I could detail his GTI.

Ok so let us get started. I am going to try something a little different this time around by accompanying the pictures with product and process information. So bare with me and hopefully you will enjoy the write up as much as I have enjoyed writing it up.

BEFORES

So before I do anything to the car I like to go around with my D40. You can use any camera with a decent quality pixel rate but I find that DSLR provides for better depth and sharpness. Even though I do a walk through at the beginning I find that the process of snapping quality pictures really helps with me with prioritizing trouble areas. If surprises pop up I make sure to call the customer to let him know of the issue before proceeding. It really saves me and customer time and hassle.







Possible bird etching issue on this particular panel.





Scratch on driver side mirror with paint transfer. Possible solutions could be heat gun and a light wipe, ISA wipe (isopropyl and water 50:50 mix), clay & clay lube and polishing.

















The GTI is obviously dull but there is also a noticeable grayish tinge but it is nothing to be overly concerned about.

WASH

Ok so Iíve done the post detail walk through now let us move on to the wash phase of the detail. After my washes I always like to snap additional pictures because you never know what could be hiding underneath all that dirt. Dirt may not be dirt and maybe a scratch.



My tools of choice for washing this GTIís paint is as follows:
2 Grit Guards
2 Sheepskin Wash Mitts
1 Detail Brush
Chemicals Guys Maxi Suds
Optimum No Rinse
Optimum Power Clean

I mix all three together. 1 oz of Maxi Suds, 1 oz of ONR and 2 oz of PC. I like a little suds so I use Maxi Suds to lift the dirt, ONR is added to soften the water and to pull the dirt away from the paintwork and PC to get rid of any existing wax or sealant even though this particular GTI did not have any protection to speak off.





The tools that I used for the wheels are:
Detail brush (which are brilliant for lug nuts)
Grit guard
One bucket
Daytona Wheel Brush (completely invaluable when cleaning inner rims)
2 Chenille wash Mitts
Chemical Guys Wheel Gel ( 1 part water 1 part Wheel Gel used directly on surface)
Optimum Power Clean (1.5 oz of Power Clean used in bucket solution)







When rinsing wheels it is always safer to wash your wheels when they have cooled down. If you rinse a vehicle that has just been driven you risk the rotor warping because the rotor is hot while the water is cold. GTI was picked up the day before so the wheels were cool so there were no issues rinsing the wheels.



Coating the caliper and wheel with Chemical Guys Wheel Gel.



CG Wheel Gel also sprayed on tires.



You can see the wheel gel working and pulling the dirt away from the tire. This will help the longevity and look of your favourite tire dressing by having a clean canvas to work on.



Here is the Daytona brush in action. I scrub by brushing in side to side and back and forth motion to get the best cleaning action. Again I canít emphasize how much itís helped me keep my hands from getting tiny cuts from the rotors.





The Daytona Brush bent and being used behind the spokes.





The chenille mitt being used for the face of the rim. Although I prefer using the detail brush or zymol brush I find that the chenille mitt saves me some time because it has more coverage. I still use the detail brush for the corners of spokes.



Detail brush being used for the lug nuts.



All cleaned up.



Whoops almost forgot the calipers. When cleaning your calipers or the inner rims if you find that itís being blocked by a spoke or caliper just roll your vehicle backward or forward to clean the previously inaccessible area.



Another example of a wheel scrub down.



Clean and Clear bucket. Keep that in mind for after the wash.



1 ounce of ONR going in the bucket.





1 ounce of Maxi Suds going into the bucket





2 ounces of Power clean going into the bucket.





A quick blast of the hose and voila! A wonderful symphony of colours.



GTI being rinsed down.





2 bucket wash method being practiced. At the beginning of the process you have two clean sheepskin wash mitts in the suds bucket while the bucket with clean water remains untouched until the first pass with the mitt on the paintwork.





Mitt doing itís thing. Always start from the top of the car down that means, roof -> pillars -> hood -> trunk -> upper panels -> lower panels and bumper.



Place your dirty mitt into the clean bucket. Give it a quick shake to loosen the dirt away from the mitt. The grit guard will do its job by keeping the dirt at the bottom.





A mitt from the suds is now being used to clean. Repeat the process until the entire vehicle is done.



Mitt from clean water bucket rung out and then placed into the suds. I made sure that the mitt I had just used on the panel did not come in contact with the mitt soaking in the clean water bucket. I remove and ring the mitt in the clean water bucket first and then transferred it into the suds bucket. Only then did I place the dirty mitt into the rinsing bucket.





Dirty mitt from an extra dirty panel.



Mitt being shook to loosen dirt.

POST WASH WALK THROUGH

Below is an assortment of scratches and oh so lovely rail dust. Did I ring my cousinís neck for it? No Comment.



















DRYING



My trusty Makita was used to knock out hidden water areas in the gas tank, in between trim areas and tiny crevices that my hands would usually be unable to get to.



For the rest of the vehicle 3 waffle weave drying towels were used. You can get away with two but I find using three much more efficient. I donít like wet towels. In terms of the quality of the waffle weave, nothing but the best should touch your paint. The last thing I am sure anyone wants is for their products used for cleaning to induce marring in the paint.





Before I forget a shot of the water after washing the GTI.



Moving onto claying. I used Riccardo Yellow and clay lube which was a mix of OPT Quick
Instant Detailer and ONR. I find using QID alone with clay lube causes hazing on the paint. Easily preventable if you dry each panel as you clay rather than leaving it to haze. I chose to use ONR with QID just because I feel the clay glides a little more with the ONR mixed in.



The Riccardo clay is rolled into a ball and then flattened out.





Here I am claying the GTI. I find when claying I use the up and down and side to side motion. I have had some clients when claying ask me why the clay at first seems to start removing a certain contaminant then kind of stops working and usually more often than not itís because they were only claying in one direction rather than in the up and down and side to side motions.

So if you notice that a contaminant is not coming be sure to do both motions and if that doesnít work bump the clays aggressiveness up but be aware than you will probably need to follow up with a polish to get rid of the light marring left by the clay.







Drying the hood with a waffle weave after claying.



When you notice the clay is starting to get loaded(dirty). Fold and flatten the clay back out and voila you have new clay. However if you drop the clay at anytime just throw the clay out. It isnít worth saving that extra little bit because dirt in the clay will end up scratching your car and that just isnít worth it.





PAINT MEASUREMENT

Now on to measuring the paint thickness of the paint. The Defelsko 6000 was used to measure the paint. The paint on the GTI was relatively healthy except for the roof where youíll see from the pictures it hit 78 microns. This area will be discussed when I start polishing.







POLISHING



My tools for polishing were 2 x Metabo PE12-175 polishers, 6Ē Sonus White Polishing Pads, 4Ē Flat LC polishing pads, 3M Sun Gun, 3M Backing Plate, Rubbish Boys Backing Plate, Meguiars 105, Meguiars 205 and Menzerna 106FF.

For most of the car except the roof Meguiars 105 was used with the 6Ē and 4Ē pads. M205 with 6Ē and 4Ē was used on the roof.

Polishing Steps
900 rpm light pressure Ė medium pressure
1100 rpm heavy pressure
900 rpm medium pressure - light pressure

When I neared the end of a pass there was almost no pressure on the pad. I lifted the rotary to make sure my arms were sustaining most of the rotaries weight. By doing this the finish that was attained in my opinion was almost LSP ready. I then followed up M105 with M205 with the same process except that I kept the RPMS at 900rpm the entire time.



I love how thick the Sonus pads are. Too bad they have been discontinued.



I apologize for the blurry pics. Itís hard to take pictures on your own thankfully on the second day my gf came by and helped towards the end of the detail.



Door ding.



After 3 passes with M105 on 4 inch pad. I could have used a more aggressive pad or even wet sanding but I didnít think it was necessary to take it to a more aggressive level when I felt that the results were more than satisfactory.



The result.



Remember the scratch and paint transfer on the side mirror? Gone.



Sorry defects were a little hard to take on the white. However in this particularly picture youíll notice the 3M sun guns reflection is a little hazy and trust me there was quite a bit of swirls.



Haziness and swirls gone.



Cleaned up.



Cleaned up.



Cleaned up.





Here I am correcting the bumper. Yes I love my shorts and my crocs. Those arenít my socks I swear.



I will be using a 4 inch LC pad with M105 on the bumper lip area. This area needed about 3 passes.





Here I am taping off the rubber near the bumper lip area. Even though I am working at such low RPMís its just good practice to tape. When using a rotary or even a DA the corners of the pad can burn subsequent perpendicular areas. Be aware and you are better safe than sorry so make sure you tape off.



Polishing away. If you look closely the pad is not touching the increased grade of the paint where the paint meets the trunk.



Now to the hatch. I propped the hatch open with a microfiber towel placed on the bumper while using a polishing bottle to prop it up. It gives me better access to the paintwork in that particular area.









Emblem before.



Emblem after with cuetip with m105 then cuetip with m205.



Hazzy and Swirly.



Cleaned up.



Cleaned up.



Yes thatís me shining a 3M sun gun on my head. No Iím not trying to get a tan and yes I was just playing around. Life isnít fun without silliness.



Closing out day one. I removed the tape that was used to protect the lower plastic trip as I was polishing the lower panels. Tape used. Two balls.



In the middle of day two refining the paint with M205 on Sonus white and checking my work.







Here I am using a MF towel to brace myself so my clothes do not come in contact with the surface of the paint. I am a heavy boy but that isnít my belly thatís my sweater.







Priming a pad with M205.







That brings an end to polishing.

POST POLISHING RINSE

The wash is to just remove any powder left on the car. Most of the polishing dust was removed via air compressor.













PRE-LSP















303 Aerospace Protectant was used on all the exterior trim.



I find that spraying product onto the MF and then wiping the applied area provides for a more uniform look. Iíve noticed when product is applied directly you have streaking issues.

















My girlfriend giving the interior a quick wipe down with Einszett Cockpit Premium.

LSP APPLICATION

LSP: Migliore Primo

My take on Primo. I applied primo by using an applicator pad and I would work two panels at a time then buff off. I found Migliore fairly hard to remove. Once I thought that I had buffed off all of the wax there would still be obvious streaking. I resorted to using quick detailer to help with the initial buffing and then would follow up with a clean MF . It also helps to have a lot of microfiber towels on hand. Look at the pictures and you be the judge. So do the ends justify the means? I like the product even though it may take me longer than usual to remove it. It looks great. Iíll give it a few more tries before I have a solid answer.















Notice the hazing near the halogens. Clarity isnít perfect because there was still wax there. On to more buffing.











Loving the deep and wet look.



On to the rest of the car.





Defying gravity. Definitely hard to get off.

AFTERS



















Outdoor Photo Session



Buffing off a little more wax.



VOILA!





















Putting on another layer of Tropicare White Pearl Dressing on the Tire. 2 coats were applied. One after polishing and one after LSP.



RainX being applied to the windows.

Exhaust tips were treated with OPT Metal Polish 0000 Steel Wool. OPT MP with MF.

VW GTI: $27,000
Cost of lunch for GF? Too Much
Grateful Cousin? Priceless

Detail Hours: 15 hrs
Camera Work: 2 Hours

OCDetailing.ca
Toronto, Ontario
nikku is offline  
Sponsored Links
Advertisement
 
post #2 of 11 Old 11-17-09, 11:53 AM
AW Resident Stormtrooper
 
Clapoti's Avatar
 
Join Date: Oct 2005
Location: The Fatherland
Age: 37
Posts: 25,346
My Mood: Bored
Wow awesome job Too bad I'm too far to have you detail my car.

I also love my shorts BTW

Clapoti is offline  
post #3 of 11 Old 11-17-09, 12:06 PM
Banned
 
Duckdog's Avatar
 
Join Date: Apr 2006
Location: The Old West
Age: 61
Posts: 30,196
Incredible work!
Duckdog is offline  
 
post #4 of 11 Old 11-17-09, 12:24 PM
AW Detailing Wanker
 
S2K2K4's Avatar
 
Join Date: Jul 2004
Location: East TN
Posts: 16,331
Garage
Send a message via AIM to S2K2K4 Send a message via Yahoo to S2K2K4 Send a message via Skype™ to S2K2K4
Nice work. That GTI was nasty.


Our Father, who art in Autos, hollowed be thy frame. Thy Horsepower come, Thy torque be fun, in Imports as in Domestics. Give us this day our daily fuel, and forgive us our hooning, as we forgive those who hoon against us, and lead us not into chrome accents, but deliver us from rice. For thine is the Cam, and the Piston, and the Rod, for ever and ever. Or until they break.. Amen.
S2K2K4 is offline  
post #5 of 11 Old 03-24-10, 12:33 PM
AW's Resident Smartass
 
TireMeltingRSX's Avatar
 
Join Date: Jun 2005
Location: Phoenix, AZ
Age: 38
Posts: 38,577
My Mood: Cheeky
Send a message via AIM to TireMeltingRSX Send a message via Yahoo to TireMeltingRSX
What an awesome step by step guide. I'm going to change the description and sticky this thread!

AWESOME WORK, AWESOME EXPLANATION, AWESOME PICTURES, AWESOME MEMBER!




2006 VBP RSX Type S
TireMeltingRSX is offline  
post #6 of 11 Old 03-27-12, 12:01 PM
Registered User
 
Join Date: Mar 2012
Posts: 6
awesome job...thanks for sharing...
janepaul is offline  
post #7 of 11 Old 12-12-12, 05:44 AM
Registered User
 
Join Date: Dec 2012
Posts: 7
Hi all this thread i think really helpful for all Nissan fans and these pictures are really good and this is good step by step guide us.
Cyril is offline  
post #8 of 11 Old 08-09-14, 01:19 PM
Registered User
 
Frosty.'s Avatar
 
Join Date: Aug 2014
Posts: 17
Wow, that was very DETAILED!
Frosty. is offline  
post #9 of 11 Old 09-07-16, 10:47 PM
AAA AUTO SPA
 
Join Date: Sep 2016
Posts: 10
Hello
Very detailed post and nice car.
AAA AUTO SPA is offline  
post #10 of 11 Old 12-09-18, 07:26 AM
Registered User
 
Join Date: Dec 2018
Posts: 2
Great! Thank you for sharing a step by step guide with us.
Travishead is offline  
post #11 of 11 Old 11-01-19, 06:47 AM
Registered User
 
Join Date: Nov 2019
Posts: 2
So long and detailed, I've learnt the tips now. Thank you!

Looking forward to new Mazda CX30 Malaysia.
Cupp is offline  
Sponsored Links
Advertisement
 
Reply

  Acura Forum : Acura Forums > Shop Talk > Detailing Tips and Tricks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Acura Forum : Acura Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome
 

Ad Management plugin by RedTyger